Description
Specification:
Power: 40W / Pair
Lumens: 4,000LM
Dimension: 3 * 1.8 * 1.8 Inch
Operating Voltage: DC 12 ~ 30V
Protection Rate: IP68 Waterproof
Material: 6063 Aluminum profile, PC Lens
Color Temperature: 6,000K-6,500K
Working Temperature: -40 ~ 85 Degree Celsius
Working Life: Delivering over 50,000 hours lifespan
PACKAGE:
2 x 3 inch LED Pods
Adjustable Mounting Brackets
Screw Set (Without switch and wiring harness)
MSgtEllis –
Nice low profile.
Very good illumination with nice low profile that does not obstruct your view when driving. Easy install, with all hardware included. The combination lighting design makes these perfect for seeing the side of the trail when the spot is aimed just above the hood. So far they are very impressive, so I hope they stand the test of time.
John –
Not the brightest but they work
So i have these .punted as ditch lights. They aren’t crazy bright in compared to my highbeams however the produce enough light to be used as chase lights or ditch lights on an overland/offroad truck or jeep.For an ATV or any similar offroad vehicle I’d say they produce plenty of light to be a main driving light
VancouverGuy –
Good/Solid light…but….
So the lights are bright and seem well made. But i am taking a star off (could argue for two off) due to: 1. The light is very yellow, not amber. 2. Zero instructions or detail sheet with it. I wanted to wire the correct fuse etc, but didn’t have the details. I pulled the info from the product details online and then did some math and figured the amps. A sheet/info would have helped. 3. The coating that is on the housing seems durable, but it was also sprayed on the threads where the bolts screw in, so they did not fit easily or well. I was worried about cross threading due to the fit and the force i had to use.As i said tho, they are bright and otherwise seem to work well. I tried to set myself up for success by using clear silicone adhesive to seal up every seem on the unit, around the lens, and around the port where the wiring comes out. I’ve had good success by doing that with other vehicle LED lights, so hopefully the same will work here.I used a Nilight wiring harness and Nilight hood mounts to complete the install.
Tim –
very bright
very bright for offroad use only
vechat m. –
Bright!
Used for chase lights they’re pretty bright
FrivolousReviewer –
Not bad
The media could not be loaded.
I needed to flip the lens so I could have the diffusion on the outside of the car on both sides. I basically was sent to left sides. Flipping the lens was actually pretty easy though. My only real complaint is the mounting bold and nut is prone to rusting but a dap of spray paint would prevent that. Bottom line these lights are great for rear dust lights. I would buy again 👍
Jon W Williams –
What others said…these are yellow
These should not be described as amber
1300Defender –
If only you would have put a gasket like is supposed to have
Received the pods all good so far. then I noticed the lenses were reversed on one of the pods….. the spot lens ( smooth lens )needs to be in the inside while the flood one is to be on the outside… they had it reversed. So I said well no big deal. So I proceeded to correct the problem then I ran into the second problem THERE IS NO GASKET… that’s why all of this lights fail or have condensation inside THIS IS A BIG PROBLEM I don’t understand why go through all the trouble to clone this light when you can’t even put a gasket to prevent water intrusion. Over all design looks great. But failed … pay attention China if the point is to make money at least do it right. Buyer just be aware of what you are getting… if only you would have put a gasket like is supposed too I still would have given 5 stars even knowing that this are not the real deal
RickD –
Suitable for Driving/DRL Lights
I was looking for a pair of small amber lights for my Ryker to use as daytime running/driving lights. These fit the bill nicely. Living in rural south Texas I see a lot of amber lights on the road at night, and most of them are really too bright for street use, especially if not aimed properly or are mounted too high. These are not as bright many similarly sized lights, but for my application that is a plus. I see a lot of reviews dinging them for lack of written instructions. There is a pigtail coming off each pod that has two wires, red and black. If you believe you need more “instruction” than that, you should probably consider having a professional install them for you.
Ricki D. –
Great Chase Lights
Had these lights on a wishlist and never really bit the bullet till now. I’m glad I did as these lights have a good-quality look and appear to be relatively bright. Mind you there isn’t a left and right light so if you want a symmetrical look you will need to pop the cover off and rotate the lens. Super easy if you ask me and allowed me to see the gasket that seals up the electrical components. Will update down the line but so far great addition to the truck.